High Grade Gold Intercept Confirmed at Windanya
Released
Released
Announcement PDF
ASX ANNOUNCEMENT
21 August 2024
Confirmation of High Grade Gold
intercept at Windanya
Dundas
Minerals Limited
Highlights
• 9.5 g/t Au (146m – 147m) assay from resample of the final six
metres in drill hole 24WDRC015
Directors
• Drill hole to be extended beyond its current depth of 150m
Non-Executive Chairman
Mark Chadwick
• Two deep drill holes to test for primary gold mineralisation west
of 24WDRC015, in the northern portion of the Aquarius gold
prospect
Managing Director
Shane Volk
Non-Executive Director
Tim Hronsky
Company Secretary
Shane Volk
Issued Capital (ASX: DUN)
Ordinary Shares: 84,628,046
Unlisted Options:
40,000,000
• Drilling scheduled to commence in September 2024
Dundas Minerals Limited (ASX: DUN) (“Dundas Minerals”, “Dundas” or
“the Company”) is actively exploring for gold at the Windanya and
Baden-Powell projects, located adjacent the Goldfields Highway ~60km
north of Kalgoorlie, Western Australia.
Assay results from 1 meter sample intervals – Windanya
The receipt of assay results for six separate one metre sample
intervals relating to the previously reported 4 meter and 2 metre
composite samples from drill hole 24WDRC015, at the Company’s
Windanya project, has confirmed the intercept of high grade gold
mineralisation.
The final six metres of the drill hole was resampled (144 metres to
150 metres). For the 146m – 147m interval the assay result was 9.5
grams per tonne (g/t) gold (Au), and for the preceding interval (145m
– 146m), 0.725 g/t Au. Refer to Table 1 for the assay results for each
1 metre interval sampled.
Encouraged by the results, the Company is planning to extend the
hole beyond its current length of 150 metres (approximately 130m
below surface), to up to 300m.
Baden-Powell &
Windanya gold
projects
Also, two additional RC drill holes, each to a planned depth of up to
300 metres are to be drilled southwest of 24WDRC015, in the
northern part of the Aquarius gold prospect (Figure 1). At Aquarius,
in November 2023, the Company reported very high grade gold in
auger sample anomalies (including: 696ppb Au; 493ppb Au and
483ppb Au). Refer to ASX Announcement dated 2 November 2023
for complete details of the auger sampling results.
The Program of Work (PoW) for the additional drilling has been
approved. Drilling is expected to commence in September 2024,
weather conditions (rainfall) permitting.
Suite 13, 100 Railway Road
Suite 13, 100 Railway
Road
Subiaco,
WA 6008
Subiaco, WA 6008
admin@dundasminerals.com
admin@dundasminerals.com
www.dundasminerals.com
www.dundasminerals.com
Page 2
Capricorn
Gold Deposit
RC Drillhole collar (2024)
ML Application Boundary
EL Boundary
Aquarius
Gold Prospect
Target area
for RC drilling
(2 holes)
Scorpio Gold
Prospect
Figure 1: Windanya RC drill collar locations (2024), plus the location
of the Capricorn gold deposit, and the Aquarius and Scorpio
gold prospects (background: regional bedrock geology)
Table 1: 24WDRC015 Assay Results from 1 metre samples
(Au 50g sample fire assay, all other elements Aqua Regia 25g sample. Refer to Table 1 for
additional details)
In the Company’s ASX Announcement of 4 July 2024, it was reported that the end-of-hole 2 metre
composite sample (148m-150m) returned an assay of 2m @ 3.142 g/t Au. It has since been
determined that this result is for the preceding 4m interval (144m-148m), with the error caused by
the misnumbering of the sample on submission to the assay laboratory. Refer to Table 2 for the
corrected details for the assay results published by the Company on 4 July 2024.
Suite 13, 100 Railway Road
Subiaco, WA 6008
admin@dundasminerals.com
www.dundasminerals.com
Page 3
Table 2: 24WDRC015 Composite Assay Results 4 July 2024 (updated)
(All elements Aqua Regia 25g sample)
Hole ID
24WDRC015
Depth
150
East
332828
North
6640063
Azimuth
o
270
Dip
o
-60
Suite 13, 100 Railway Road
Subiaco, WA 6008
admin@dundasminerals.com
www.dundasminerals.com
Page 4
Authorised by: Shane Volk – Managing Director
About Dundas:
Capital Structure:
Dundas Minerals Limited (ASX: DUN) is a battery-minerals and gold focussed exploration company exploring in the gold-rich
Kalgoorlie region, and southern Albany-Fraser Orogen, Western Australia. In the Kalgoorlie region the Company has an option
agreement with ASX listed Horizon Minerals Limited (ASX: HRZ) to acquire an 85% interest in two gold projects, Windanya
(25,000oz Au inferred gold resources), and Baden-Powell (23,000oz Au inferred gold resources), and in the southern Albany-Fraser
the Company holds various exploration licences and exploration rights for gold, copper and nickel.
Ordinary shares on issue (DUN): 84,628,046; Unlisted Options: 15,000,000 (Exp. 16-06-29 Ex. $0.033); 15,000,000 (Exp. 16-06-29 Ex.
$0.0374); 3,000,000 (Exp. 3-11-24 Ex. $0.30); 5,000,000 (Exp. 1-7-26 Ex. $0.25 & $0.30); 2,000,000 (Exp. 10-11-26 Ex. $0.25 & $0.30)
COMPETENT PERSONS STATEMENTS
The information in this announcement that relate to the Windanya soil sampling program are extracted from the ASX Announcement titled
“Exceptionally High Grade Gold in Soils Anomalies at Windanya Project” published on 2 November 2023. The report is available to view on
the Company’s web site: www.dundasminerals.com. The Company confirms that it is not aware of any new information or data that materially
affects the information included in the original ASX Announcement. The Company confirms that the form and context in which the Competent
Person’s findings are presented in this report, have not been materially modified from the original ASX market announcement.
The exploration program and results reported in this Announcement was completed by Mr David Thompson, a Member of the Australian
Institute of Geoscientists. Mr Thomson has sufficient experience relevant to the style of mineralisation and to the type of activity described in
this Announcement to qualify as a competent person as defined in the 2012 Edition of the “Australasian Code for Reporting of Exploration
Results, Mineral Resources and Ore Reserves”. Mr Thompson is a consultant to Dundas Minerals Limited and consents to the inclusion in this
Announcement of the matters based on his information in the form and content in which it appears.
DISCLAIMERS AND FORWARD-LOOKING STATEMENTS
This announcement contains forward looking statements. Forward looking statements are often, but not always, identified by the use of words
such as "seek", “target”, "anticipate", “forecast”, "believe", "plan", "estimate", "expect" and "intend" and statements that an event or result
"may", "will", "should", "could" or "might" occur or be achieved and other similar expressions.
The forward-looking statements in this announcement are based on current expectations, estimates, forecasts and projections about Dundas
and the industry in which it operates. They do, however, relate to future matters and are subject to various inherent risks and uncertainties.
Actual events or results may differ materially from the events or results expressed or implied by any forward-looking statements. The past
performance of Dundas is no guarantee of future performance.
None of Dundas’s directors, officers, employees, agents or contractors makes any representation or warranty (either express or implied) as to
the accuracy or likelihood of fulfilment of any forward-looking statement, or any events or results expressed or implied in any forward-looking
statement, except to the extent required by law. You are cautioned not to place undue reliance on any forward-looking statement. The forwardlooking statements in this announcement reflect views held only as at the date of this announcement.
Suite 13, 100 Railway Road
Subiaco, WA 6008
admin@dundasminerals.com
www.dundasminerals.com
JORC Code, 2012 Edition – Table 1 report template
Section 1 Sampling Techniques and Data
(Criteria in this section apply to all succeeding sections)
Criteria
JORC Code explanation
Sampling
• Nature and quality of sampling (e.g., cut channels, random chips, or
techniques
specific specialised industry standard measurement tools appropriate to
the minerals under investigation, such as down hole gamma sondes, or
handheld XRF instruments, etc.).
• Include reference to measures taken to ensure sample representivity and
the appropriate calibration of any measurement tools or systems used.
• Aspects of the determination of mineralisation Material to the Public
Report.
• Drill type and details (e.g. core diameter, triple or standard tube, depth
Drilling
of diamond tails, face-samplingbit or other type, whether core is oriented
techniques
and if so, by what method, etc.).
Drill sample
recovery
Logging
Sub-sampling
techniques and
sample
preparation
• Method of recording and assessing sample recoveries and results.
• Measures taken to maximise sample recovery and ensure representative
nature of the samples.
• Whether a relationship exists between sample recovery and grade and
whether sample bias may have occurred due to preferential loss/gain of
fine/coarse material.
• Whether core and chip samples have been geologically and
geotechnically logged to a level of detail to support appropriate Mineral
Resource estimation, mining studies and metallurgical studies.
• Whether logging is qualitative or quantitative in nature.
• The total length and percentage of the relevant intersections logged.
• If core, whether cut or sawn and whether quarter, half or all core taken.
• If non-core, split type, and whether sampled wet or dry.
• For all sample types, the nature, quality and appropriateness of the
sample preparation technique.
• Quality control procedures adopted to maximise representivity of
samples.
• Measures to ensure that the sampling is representative of the in-situ
material collected, including for instance results for field duplicate/secondhalf sampling.
• Whether sample sizes are appropriate to the grain size of the material
sampled.
5
Commentary
• 1m cuttings were collected in buckets and put on the ground in rows of 20
piles. Samples were taken by aluminium scoop from the 1m piles on the
ground and put into numbered calico sample bags.
• Regular cleaning by air and by hand was done to avoid contamination by
sticky clay material.
• Reverse circulation drilling was used to obtain 1m cuttings from which a
representative sample was collected by handheld aluminium scoop.
• Slimline (4½ in diameter) RC drilling was used with a face-sampling
hammer bit.
• It was a truck mounted drill rig (X300 4 x 4 MAN) that is a modified X150
with a 1050/350 compressor and a 636 Hurricane booster.
• Sample volumes were visually assessed, no anomalous volumes were
observed. Samples were generally dry, but in rare cases damp samples
were noted, mostly the meter after rod changes.
• Regular cleaning of the cyclone, to avoid build-up of clayey material.
• Sample recovery was generally good; no sample bias was observed.
• Chips were collected in chip tray and logged qualitatively by the geologist.
• Logging was qualitative in nature.
• The complete holes were logged in full.
• Samples were collected from the 1m sample piles by aluminium scoop. In
the case of composite, up to 4 scoops were combined into one sample for
assaying. The whole sample was pulverised in the laboratory and a 50g
charge taken for fire assay, and/or 25g sample in the case of Aqua Regia.
• The sample preparation is considered appropriate for the type of sampling.
• Certified Reference Materials and field duplicates were inserted in the
sample submission at a rate of 1 in 25. In addition, internal standards and
repeat assays were used by the laboratory.
• The sample sizes were considered appropriate for the grain size of the
material.
Criteria
Quality of assay
data and
laboratory tests
JORC Code explanation
Commentary
• The nature, quality and appropriateness of the assaying and laboratory
procedures used and whether the technique is considered partial or total.
• For geophysical tools, spectrometers, handheld XRF instruments, etc.,
the parameters used in determining the analysis including instrument
make and model, reading times, calibrations factors applied and their
derivation, etc.
• Nature of quality control procedures adopted (e.g. standards, blanks,
duplicates, external laboratory checks) and whether acceptable levels of
accuracy and precision have been established.
Verification of
sampling and
assaying
• The verification of significant intersections by either independent or
alternative company personnel.
• The use of twinned holes.
• Documentation of primary data, data entry procedures, data verification,
data storage (physical and electronic) protocols.
• Discuss any adjustment to assay data.
• Accuracy and quality of surveys used to locate drill holes (collar and
down-hole surveys), trenches, mine workings and other locations used in
Mineral Resource estimation.
• Specification of the grid system used.
• Quality and adequacy of topographic control.
• Samples were submitted to the Intertek Genalysis laboratory in Kalgoorlie
for assaying by method AR25/MS33 (25g sample, reading by ICP-MS),
and for gold by method FA50/MS (50g sample, fire assay ICP-MS). Both
are standard industry practice and AR25/MS33 is considered a total
assay technique.
• Not applicable.
• Laboratory QA/QC involves the use of internal lab standards using
certified reference material, blanks, splits and replicates as part of the inhouse procedures. QC results (blanks, duplicates, standards) were in line
with commercial procedures, reproducibility and accuracy.
• The results have been reviewed by the Company.
• No twinning of drillholes has been undertaken.
• Data were collected in Logchief and later transferred to the Company’s
independently managed database.
• No adjustments were made.
Location of
data points
Data spacing
and distribution
Orientation of
data in relation
to geological
structure
Sample security
• Data spacing for reporting of Exploration Results.
• Whether the data spacing and distribution is sufficient to establish the
degree of geological and grade continuity appropriate for the Mineral
Resource and Ore Reserve estimation procedure(s) and classifications
applied.
• Whether sample compositing has been applied.
• Whether the orientation of sampling achieves unbiased sampling of
possible structures and the extent to which this is known, considering the
deposit type.
• If the relationship between the drilling orientation and the orientation of
key mineralised structures is considered to have introduced a sampling
bias, this should be assessed and reported if material.
• The measures taken to ensure sample security.
6
• Drillhole collars were surveyed with handheld GPS with horizontal
accuracy of ±3m. Data are recorded in UTM coordinates, zone 51S
Geocentric Datum of Australia 1994 (GDA-94).
• Elevation was estimated to the nearest metre from Geoscience Australia
DTM, which is more accurate than handheld GPS elevation data.
Downhole surveys were undertaken by gyro with readings taken every 5m
along the drill trace.
• Topographic control is considered adequate at this stage. Should the data
be subsequently used in a Mineral Resource Estimation, the collars can
be surveyed by DGPS.
• Drillholes were irregularly spaced, as this was a reconnaissance program,
targeting various under-cover areas for gold mineralisation.
• No attempt is made at this stage to undertake Mineral Resource or Ore
Reserve estimations.
• 1 metre samples have been taken for hole 24WDRC015.
• Holes were angled 60° towards 270°, roughly perpendicular to the regional
strike and interpreted structures, but there is considerable uncertainty
about the attitude of possible structures.
• At this stage, there is insufficient data to assess the possibility of sampling
bias.
• Samples were collected in calico bags, in turn placed into larger bags that
were delivered to the Intertek laboratory in Kalgoorlie by a consultant to
the Company.
Criteria
JORC Code explanation
Audits or reviews • The results of any audits or reviews of sampling techniques and data.
Commentary
• None.
Section 2 Reporting of Exploration Results
(Criteria listed in the preceding section also apply to this section)
Criteria
JORC Code explanation
Mineral tenement and
• Type, reference name/number, location and ownership
land tenure status
including agreements or material issues with third parties such
as joint ventures, partnerships, overriding royalties, native title
interests, historical sites, wilderness or national park and
environmental settings.
• The security of the tenure held at the time of reporting along with
any known impediments to obtaining a licence to operate in the
area.
Commentary
• The results reported in this Announcement are from granted Licence
P24/5059. The licence is 100% owned by Black Mountain Gold Limited, a
wholly owned subsidiary of Horizon Minerals Limited (ASX: HRZ). Dundas
Minerals has an option to acquire an 85% joint venture interest in the
tenement on or before 29 August 2025 (refer ASX Announcement dated 30
August 2023 for complete details).
• The tenement is in good standing and there are no known impediments to
the security of, and access to the tenements.
Exploration by other
parties
• Acknowledgment and appraisal of exploration by other parties.
• Horizon Minerals Limited has undertaken substantial previous exploration
on the tenements since 2017, including soils sampling, air core and RC
drilling, and published an inferred Mineral Resource estimation for the
Capricorn prospect within P24/5057. Previous exploration has also been
undertaken by Heron Resources Limited (2006-10), and Vale (2008).
Geology
• Deposit type, geological setting and style of mineralisation.
• The exploration target is Archaean lode gold on the western limb of the
Bardoc-Broad Arrow syncline.
Drillhole Information
• A summary of all information material to the understanding of
the exploration results including a tabulation of the following
information for all Material drill holes:
o easting and northing of the drill hole collar
o elevation or RL of the drill hole collar
o dip and azimuth of the hole
o down hole length and interception depth
o hole length.
• If the exclusion of this information is justified on the basis that
the information is not Material and this exclusion does not detract
from the understanding of the report, the Competent Person
should clearly explain why this is the case.
• In reporting Exploration Results, weighting averaging
techniques, maximum and/or minimum grade truncations (eg
cutting of high grades) and cut-off grades are usually Material
and should be stated.
• Where aggregate intercepts incorporate short lengths of highgrade results and longer lengths of low-grade results, the
procedure used for such aggregation should be stated and
• Tabulated in the main text.
Data aggregation
methods
7
• Not applicable.
Criteria
Relationship between
mineralisation widths
and intercept lengths
Diagrams
Balanced reporting
Other substantive
exploration data
Further work
JORC Code explanation
some typical examples of such aggregations should be shown
in detail.
• The assumptions used for any reporting of metal equivalent
values.
• These relationships are important in the reporting of Exploration
Results.
• If the geometry of the mineralisation with respect to the drill hole
angle is known, its nature should be reported.
• If it is not known and only the down hole lengths are reported,
there should be a clear statement to this effect (eg ‘down hole
length, true width not known’).
• Appropriate maps and sections (with scales) and tabulations of
intercepts should be included for any significant discovery being
reported. These should include, but not be limited to a plan view
of drill hole collar locations and appropriate sectional views.
• Where comprehensive reporting of all Exploration Results is not
practicable, representative reporting of both low and high
grades and/or widths should be practiced to avoid misleading
reporting of Exploration Results.
Commentary
• Down hole length, true width not known.
• Included in the main text.
• Not applicable.
• Other exploration data, if meaningful and material, should be •
reported including (but not limited to): geological observations;
geophysical survey results; geochemical survey results; bulk
samples – size and method of treatment; metallurgical test
results; bulk density, groundwater, geotechnical and rock
characteristics; potential deleterious or contaminating
substances.
• The nature and scale of planned further work (e.g. tests for •
lateral extensions or depth extensions or large-scale step-out
drilling).
• Diagrams clearly highlighting the areas of possible extensions,
including the main geological interpretations and future drilling
areas, provide this information is not commercially sensitive.
8
Not applicable, no other material exploration data.
Follow-up work may include drilling extending the depth of drill hole
24WDRC015 and RC drilling in an as yet untested area south of the
Capricorn Gold deposit.
Share your feedback
Discover